Sonnax replacement part.
2.50" overall length X .032" thick, .532" pin opening with 1.50" pin center.
1.156" outside diameter X .63" outside diameter X .033" thick. 1 per bag.
This shaft has been redesigned for use with aftermarket 30 spline input shafts. This shaft is heat treated alloy steel. No machining required. This is a direct replacement part. More Information
This retainer is stamped from high strength steel and is designed to resist defection.Use with springs 28320A. More Information
2.196" overall length X .032" thick, .629" pin opening with 1.85" pin center.
(Figure 8 washer, 2.50" overall length X .032" thick with 1.50" pin center). 6 Per bag. More Information
12 piece set. This is a direct replacement part. More Information
Contains 12 thin and 3 thick spacers.
More Information
This hub is designed for extra heavy-duty drag racing.Machined from high quality, medium-carbon steel forging.All splines are precision machined. Unique lube hole patterndesigned to reduce drag on the frictions in low gear.Five lightening holes reduce weight without compromising strength.This hub will accept 5 X .094" friction plates for added load capacity.
This hub is designed for extra heavy-duty drag racing.Machined from high quality, medium-carbon steel forging.All splines are precision machined.Unique lube hole pattern designed to reduce drag on the frictions in low gear.Five lightening holes reduce weight without compromising strength.Hub height 1.488".
This hub is designed for extra heavy-duty drag racing.Machined from high quality, medium-carbon steel forging.All splines are precision machined.Unique lube hole pattern designed to reduce drag on the frictions in low gear.This hub is similar to 28304 but without the lightening holes.
Powerglide transmission partsThis hub is designed for extra heavy-duty drag racing. Machined from high quality, medium-carbon steel forging. All splines are precision machined. Unique lube hole pattern designed to reduce drag on the frictions in low gear. Hub height 1.488". (Same as 28304-01 without the holes)
24 Per bag.See 28320A for reverse return springs.
POWERGLIDE Large Wear Plate High Clutch Drum. More Information
5 Per bag. More Information
These bolts are longer for use with aluminum pans. 14 studs and nuts per pack.
Hardened replacement pump bolts and nuts. Prevent wearing of the case from repeated dissembles. This kit contains 7 hardened pump bolts and nuts.
This is a threaded plug to replace the vacuum modulator. More Information
Made from hardened and tempered alloy steel. Prevents deflection and bending.More Information
This is a high strength support made from 6061-T6 billet aluminum, with pre-installed roller bearing in place of the bushing, this is a support designed for used in drag racing, eliminating the provisions for the governor. No machining required. More Information
.061" (1.54mm) thick X 2.688" outside diameter X 1.998" inside diameter.
.078" (1.98mm) thick X 2.688" outside diameter X 1.998" inside diameter.
Servo piston with gasket and o-rings.More Information
This piston accept both teflon and metal sealing rings. Replacement teflon seals #18608T (2 reqiured). More Information
This Purple Anodized Aluminum cover is designed to replace other coversand requires no modifications to the case.It utilizes a gasket and o-ring for better sealing and is strongerto handle higher pressures, mounting bolts and plug are also included.
The kit contains a gasket, piston o-rings, piston, cover o-ring, bolts and cover.
The kit contains a gasket, cover o-ring, 2 teflon piston seals, bolts, piston, cover and cover plug. More Information
2 Required.
28755-07 POWERGIDE High Clutch Drum Small Lip Seal. 1 per bag.
Outer Lip Seal, 1 Per bag.
This prevents the throttle cable from being pulled out of adjustment at full throttle. Fits on the upper end of the inner cable.
Sonnax transmission partsMade from high tensile springs. Spring ends are close-wound and match ground to uniform length. Specifically made for trans brake equipped Powerglides. 17 Per bag.
This has a hardened comb cam area to prevent wear. Forged steel lever prevents cracking at the clamp.More Information
Sonnax 28861-03 Powerglide detent spring.
Lever can be mounted in the up or down position. Plated with zinc for corrosion protection. No case modifications required. More Information
2 required.
This is a direct replacement TORRINGTON bearing assembly.
More Information****NO LONGER AVAILABLE*****
More Informationno longer available 04.12.
Solid aluminum with lip seals. More Information
Powerglide transmission filter extension. Use with stock Powerglide transmission filter. More Information
Powerglide transmission pan use with filter extensions 28801-S09K, 28801-S10K and 28801-S11KMore Information
This cable corrector adjusts the geometry on the TV linkage preventing the throttle cable from being pulled out of adjustment at full throttle.More Information Replaces AS2-02K
Throttle Cable & TV Cable Bracket 200-4R 200C 4L60 AOD.More Information
Powerglide Bearing Kit for high performance..More Information
POWERGLIDE, GEAR PLANET RING 1.80 RATIO
Sonnax high clutch drum 28755 is a direct replacement for the OE drum. More Information
